[Full-Version] 2023 Updated Network Appliance Study Guide NS0-593 Dumps Questions
Newest NS0-593 Exam Dumps Achieve Success in Actual NS0-593 Exam
NEW QUESTION # 20
A 2-node cluster hosts only NAS data UFs. Allnodes lose access to the cluster network.
Referring to the exhibit, which statement is correct?
- A. NAS data UFs are accessible on only the node that has Epsilon.
- B. No takeover event will occur and NAS data UFs will not be accessible.
- C. All nodes in the cluster reset and NAS data UFs are not accessible after reboot.
- D. Both nodes race to takeover the other, one node will takeover the other node.
Answer: C
NEW QUESTION # 21
You are attempting to connect a NetApp ONTAP cluster to a very complex network that requires LIFs to fail
over across subnets.
How would youaccomplish this task?
- A. Configure VIP LIFs using BGP.
- B. Configure a I IF failover policy for each subnet inside a single broadcast domain.
- C. Configure an equal number of UFs on each subnet.
- D. Configure VIP LIFs using OSPF.
Answer: A
NEW QUESTION # 22
Your customer has deployed a two petabyte NetAppONTAP FlexGroup volume across their 4-node ONIAP
9.8 cluster. They plan to store over three billion files. They want to prevent file 10 conflicts since files are
placed into the FlexGroup volume.
In this scenario, which two NFS SVM parameters should be enabled? (Choose two.)
- A. -v3-64bit-identifiers
- B. -v4-64bit-idantifiers
- C. -v4-fsid-change
- D. -v3-fsid-change
Answer: A,D
NEW QUESTION # 23
You have connection Issues from a Linux host to an AFF A400 FC LUN. You are asked by support to run the
NetApp sanlun command to provide troubleshooting information.
Which NetApp software package must be installed on the host?
- A. Host Utilities package
- B. Virtual Storage Console
- C. Inventory Collect Tool
- D. SnapDrive for UNIX
Answer: A
NEW QUESTION # 24
Which two automation methods does NetApp ONTAP Select support? (Choose two.)
- A. Docker
- B. Anslble
- C. REST
- D. PHP
Answer: B,C
NEW QUESTION # 25
A customer reports that some of their client computers are unable to access a FlexGroup over CIFS. This
problem involves only their older Windows XP clients and some printers and scanners.
In this scenario, which statement Is correct?
- A. These systems use the SMQI protocol which Is an unsupported feature in FlexGroup
- B. FlexGroup requires CIFS shares to use the Continuously Available Feature, which these clients do not
support. - C. These systems use Offloaded Data Transfer, which is an unsupported feature in FlexGroup.
- D. FlexGroup requires CIFS shares to be located in qtrees, which these clients do not support.
Answer: B
NEW QUESTION # 26
A storage administrator reports that a monitoring toot is reporting that the storage controller reads between
90% to 93% CPU use. You run the sysstat -m command against thenode in question.
Referring to the exhibit, which statement is correct?
- A. You should immediately investigate further bygathering perfstat data and opening a support case.
- B. High network exempt use could be a problem.
- C. The customer should be advised to exclude certain workflows to reduce use.
- D. The CPU Is not a first-order monitoring metric for ONTAP.
Answer: A
NEW QUESTION # 27
You Just used the CLI to create a NetApp ONTAP FlexGroup Volume on a NetApp Cloud Volumes ONTAP
instance. After creation, you notice odd behavior in NetApp Cloud Manager.
In this scenario,what Is the reason for this behavior?
- A. Cloud Manager must be used to provision the FlexGroup volume.
- B. The Capacity Management Mode within Cloud Manager should be set to Manual.
- C. The Capacity Management Mode within Cloud Manager should be set to Automatic.
- D. Cloud Volumes ONTAP does not support FlexGroup volumes.
Answer: A
NEW QUESTION # 28
You created a new NetApp ONTAP FlexGroup volume spanning six nodes and 12 aggregates with a total size
of 4 TB. You added millions of files to the FlexGroup volume with a flat directory structure totaling 2 TB, and
you receive anout of apace error message on your host.
What would cause this error?
- A. The maximum number of volume constituents has been reached in the ONTAP software.
- B. The maxdirsize Is exceeded in the ONTAP software.
- C. All constituent volumes are full.
- D. The inode limit is exceeded in the ONTAP software.
Answer: D
NEW QUESTION # 29
A customer calls you to troubleshoot a network issue. The customer wants to create a packet trace for allclients
on the 192.168.9.0/24 subnet.
Referring to the exhibit, on which interface do you have to run the packet trace?
- A. a0a-322
- B. a0a-456
- C. e2a-1092
- D. e2a-100
Answer: C
NEW QUESTION # 30
Your customer noticed in NetApp Active IQ that their NetApp Cloud Volumes ONTAP forAzure HA solution
is no longer sending AutoSupport messages over HTTPS. A support ticket has been opened to find out why.
No changes have been made to the Cloud Volumes ONTAP for Azure HA environment.
In this scenario, which two autosupport command parameters should be used to validate that AutoSupport Is
working properly? {Choose two.)
- A. -mail-hosts
- B. -proxy-url
- C. -transport
- D. -to
Answer: A,B
NEW QUESTION # 31
Recently, a CIFS SVM was deployed and is working. The customer wants to use the Dynamic DNS(DDNS)
capability available in NetApp ONTAP to easily advertise both data UFs to their clients. Currently. DNS is
only responding with one data LIF. DDNS is enabled on the domain controllers.
Referring to the exhibit, which two actions should be performed to enable DDNS updates to work? (Choose
two.)
- A. Disable the -vserver-fqdn parameter for the SVM DDNS services.
- B. Enable the -use-secure parameter for the SVM DDNS services.
- C. Enable the -is-enabledparameter for the SVM DDNS services
- D. Remove the NFS protocol from the cifs_01 data LIF.
Answer: A,C
NEW QUESTION # 32
After a motherboard replacement on a NetApp AFF A300 in a SAN environment, the customer states that
ports 0e and 0f are unable toconnect to the fabric. The ports report "offline".
What would you examine first to troubleshoot the issue?
- A. storage port show command output
- B. system node hardware unified-connect show command output
- C. vserver fcp interface show command output
- D. vserver fcp wwpn-alias show command output
Answer: A
NEW QUESTION # 33
You are trying to deploy a Connector in the AWScloud from NetApp Cloud Manager. The deployment fails
and shows the message 'Insufficient permissions to deploy Cloud Connector". You have verified the AWS
access key and the AWS secret key.
In this scenario, what Is the reason that the deployment failed?
- A. The Connector can be deployed only inAWS GovCloud (US).
- B. The required Identity and Access Management (IAM) policies were not Installed.
- C. The user lacks the permission to deploy within Cloud Manager.
- D. No AWS Marketplace subscription is associated with Cloud Manager.
Answer: C
NEW QUESTION # 34
Your customer complains about missing volume snapshot copies on a SnapMlrror destination. While
investigating this case, you notice an executed SnapMirror resync operation in the event logs of the system.
In this scenario, what Is the cause of this problem?
- A. The autodelete option removed Snapshot copies before the resync.
- B. Newer Snapshot copies than the common snapshot that was chosen for resync were removed
automatically at the destination. - C. Snapshot copies were manually removed from the destination after the resync.
- D. NetApp ON TAP System Manager removed these snapshot copies due to a snapshot schedule.
Answer: C
NEW QUESTION # 35
You are optimizing your Cloud Volumes ONTAP. For interoperability and consolidation purposes, you need
to know the storagelimits.
In this scenario, which source should be reviewed?
- A. Cloud Central
- B. NetApp Cloud Volumes ONTAP Release Notes
- C. Hardware Universe
- D. Interoperability Matrix Tool (IMT)
Answer: B
NEW QUESTION # 36
Your customer mentions that they have accidentally destroyed both rootaggregates in their two-node cluster.
In this scenario, what are two actions that must be performed? (Choose two.)
- A. Re-create the cluster from the local backup.
- B. Install ONTAP from a USB device.
- C. Rejoin the second node to the re-created cluster.
- D. Re-create the cluster from the remote backup.
Answer: B,C
NEW QUESTION # 37
A customer with an FC MetroClusterconfiguration that is running NetApp ONTAP 9.8 software experienced a
site outage and wants to know why the MetroClusler configuration did not switch over to the other site.
What are two reasons for this problem? (Choose two.)
- A. An ISL link was not operating at 16Gbps.
- B. The ISLs were down between the sites.
- C. The site had unmirrored aggregates.
- D. There was a failed PSU inthe switchover site.
Answer: C,D
NEW QUESTION # 38
Your customer Informs you about SnapMlrror problems after upgrading NetApp ONTAP software to a newer
version. After investigating the event logs and the SnapMirror history, you see information about delayed
updates of the SnapMirror relationships.
How would your customer prevent such problems in the future?
- A. Verify that the cabling of the hardware port that Is responsible for SnapMirror transfers Is correct.
- B. Quiesce the SnapMirror relationships before upgrading the ONTAP software.
- C. Delete the SnapMirror relationships and create them new after upgrading the ONTAP software.
- D. Modify the schedules of the SnapMirror relationships after upgrading the ONTAP software.
Answer: A
NEW QUESTION # 39
A customer wants to connect a NetApp AFF A700 system to a 40GbE switch. The controllers have a 10/40G
Ethernet card in slot 4 for this purpose. The link comes up fine on node 2,but it will not come up on node 1.
You look at the AutoSupport data for the nodes in question and see the output shown in the exhibit.
What is the cause of the customer's problem?
- A. The incorrect cable is used.
- B. The ports are configured for 4x10Gbit instead of 40Gbit.
- C. The cable is plugged in upside down.
- D. The port has an incorrect SFP inserted.
Answer: B
NEW QUESTION # 40
You recently discovered the error message shown below in your ONTAP logs.
What should be your first action to correct this Issue?
- A. Use the wafliron command against my_data_vol to solve the inconsistency on the volume.
- B. Use the storage takeover command on the storage controller that contains my_data_vol.
- C. Determine the root cause behind the inconsistency before attempting any recovery procedure.
- D. Power cycle all the disk storage shelves that contain drives of the aggregate with the my_data_vol
volume.
Answer: D
NEW QUESTION # 41
Your customer has mounted an NFS SVM from a Linux client unci performance is very poor. The customer is
certain that they have jumbo frames enabled. They have verified an MTU of 9000 on both the Linux client and
the broadcast domain on the NetApp ONTAP 9.8 cluster.
Referring to the exhibit, which ONTAP command will help isolate a possible MTU mismatch?
- A.
- B.
- C.
- D.
Answer: A
NEW QUESTION # 42
You have a customer who is concerned with high CPU and disk utilization on their SnapMirror destination
system. They are worried about high CPU and disk usage without any user operations.
In this situation, what should you tell the customer?
- A. Explain that background tasks such as SnapMirror throttle up in the absence of user workload.
- B. Suggest that the customer throttle their SnapMirror relationships to reduce resource consumption.
- C. Explain that only user workload should use the CPU and Investigate further.
- D. Suggest that the customer manually cancel any scanners on the destination to reduce CPU usage.
Answer: D
NEW QUESTION # 43
Your customer installed the shelf firmware for their NS224 shelf over a week ago, and the firmware has
notupgraded on shelf 1 module B. The customer wants to know what the next steps would be to get the
firmware upgraded after verifying that the shelf firmware is indeed loaded onto the system.
Which step would you perform to complete the firmware upgrade?
- A. Reseat the disk in Bay 0.
- B. Reseat the NSM100 module.
- C. Reseat the PSU of the shelf.
- D. Power cycle the shelf.
Answer: D
NEW QUESTION # 44
......
Updated Network Appliance NS0-593 Dumps – Check Free NS0-593 Exam Dumps: https://pass4itsure.passleadervce.com/NetApp-NCSE/reliable-NS0-593-exam-learning-guide.html